|
Card board form, layered with duct tape, not a really great idea, I think muffler tape would be better, as it would be more heat
Card board form, layered with duct tape, not a really great idea, I think muffler tape would be better, as it would be more heat resistant
Date: 09/08/2004
Views: 597
|
Inside the completed vent housing.
Inside the completed vent housing.
Date: 09/08/2004
Views: 441
|
Housing sitting in place, driver's side
Housing sitting in place, driver's side
Date: 09/08/2004
Views: 429
|
Passenger's side view of housing.
Passenger's side view of housing.
Date: 09/08/2004
Views: 479
|
Still need to make the duct that will connect to the heater.
Still need to make the duct that will connect to the heater.
Date: 09/08/2004
Views: 504
|
|
Guess if I am going to make the rest of the Tranny hump look nice, time to retire this old boot.
Guess if I am going to make the rest of the Tranny hump look nice, time to retire this old boot.
Date: 09/09/2004
Views: 506
|
When I replace these with factory rubber ones, they look like this 3 years later.
When I replace these with factory rubber ones, they look like this 3 years later.
Date: 09/09/2004
Views: 508
|
Let's see how long vinyl lasts.
Let's see how long vinyl lasts.
Date: 09/09/2004
Views: 460
|
Shiny new paint on the ring no less...
Shiny new paint on the ring no less...
Date: 09/09/2004
Views: 520
|
Even if it only lasts 2 years, it sure looks a lot nicer than that other thing.
Even if it only lasts 2 years, it sure looks a lot nicer than that other thing.
Date: 09/09/2004
Views: 547
|
|
Here is how I am going to connect the duct to the heater. This was a PVC "T" fitting. the white part is the part I cut
Here is how I am going to connect the duct to the heater. This was a PVC "T" fitting. the white part is the part I cut off.
Date: 09/09/2004
Views: 456
|
This is the view the shifter would have of the connector
This is the view the shifter would have of the connector
Date: 09/09/2004
Views: 444
|
The "T" sticking through the housing of the duct.
The "T" sticking through the housing of the duct.
Date: 09/09/2004
Views: 491
|
yes, it does include a pop can, some PVC pipe, and card board, and a long piece of ABS plastic, but it flows air well.
yes, it does include a pop can, some PVC pipe, and card board, and a long piece of ABS plastic, but it flows air well.
Date: 09/09/2004
Views: 519
|
DONE!!
View from driver's side
DONE!!
View from driver's side
Date: 09/10/2004
Views: 447
|
|
If I had both of those emblems, I would have probably gone with a Bow tie emblem there.
If I had both of those emblems, I would have probably gone with a Bow tie emblem there.
Date: 09/10/2004
Views: 490
|
The new shift boot sure looks good with the new duct/console
The new shift boot sure looks good with the new duct/console
Date: 09/10/2004
Views: 507
|
It's the cheap carpet you buy in a 6ft roll from Walmart or Kmart for about $10-$11. All Totalled up, this console would cost ab
It's the cheap carpet you buy in a 6ft roll from Walmart or Kmart for about $10-$11. All Totalled up, this console would cost about $26-$30 to duplicate, minus the emblem of course.
Date: 09/10/2004
Views: 618
|
|
|
